Sony VCR Universal Remote Codes

We have listed all of the Universal Remote Codes for Sony Soundbar in this blog post, but if you have any questions regarding them or if you see that we have omitted any codes, please leave a comment and we will correct the errors as well as add the missing Sony Soundbar remote codes.

Contents

Sony VCR Universal Remote Codes List

Brand NameCodes
Sony301,302,303
Admiral (M. Ward)327
Aiwa338,344
Audio Dynamic314,337
Broksonic319,317
Canon309,308
Citizen332
Craig302,332
Criterion315
Curtis Mathis304,338,309
Daewoo341,312,309
DBX314,336,337
Dimensia304
Emerson319,320,316,317,318,341
Fisher330,335
Funai338
General Electric329,304,309
Go Video322,339,340
Goldstar332
Hitachi306,304,305,338
Memorex309,335
Minolta305,304
Mitsubishi / MGA323,324,325,326
Multitech325,338,321
NEC314,336,337
Optimus327
Panasonic308,309,306,307
Pentax305,304
Philco308,309
Philips308,309,310
Pioneer308
Quasar308,309,306
RCA / Proscan304,305,308,309,311,312,313,310,329
Realistic309,330,328,335,324,338
Sansui314
Samsung322,313,321
Sanyo330,335
Scott312,313,321,335,323,324,325,326
Sharp327,328
Sylvania308,309,338,310
Symphonic338
Tashiro332
Tatung314,336,337
Teac314,336,338,337
Technics309,308
Toshiba312,311
Wards327,328,335,331,332
Yamaha314,330,336,337
Zenith331

How to Program Sony Universal Remote Without Codes

All universal remote control codes are processed by the remote’s scanning procedure in the auto search method. To configure the control, it scans one code at a time to determine the correct remote code that works with your remote. The steps listed below should be followed:

  1. “Switch On” the smart device like “TV” that you want the universal remote to operate.
  2. “Turn on” the remote, tap on the device button (TV, DVD, CBL and OK/SEL) for 3 seconds. The LED light indicates the device is ready to program.
  3. Point out the remote to device and click on “CH+” & “CH-“ switches. Remote will show on/off signals. Press “up” or “down” key continuously till the device will turn off.
  4. Verify the code by clicking on “power” key. Device should turn on. If it starts, try changing the channel to verify that remote is programmed correctly.
  5. Now tap the “device” button to save the code. LED of Device will blink twice for confirming the code stored.

How to Program Sony Universal Remote With Manual Method

By using the keycode we can easily program a universal remote and the keycode identifies the make and model of your equipment.

  1. First you need to “Turn The Device On”
  2. Press the “TV” on your “Sony universal remote”
  3. Now press and hold the “Setup button” of the Universal Remote until it shows the “Light Flash” (It means it is in “Learning mode”)
  4.  Finally enter the “Keycode” which you collected from the programing guide (Instructions Booklet)
  5. Once you’ve done this procedure, just “point your remote at the TV” and then “Press And Hold The Power” button
  6. You can release the “Power Button” whenever the screen switches off.

That’s all there is to it; your TV should now operate flawlessly with the universal remote control. If not, try repeating the process with a new code from the same section of the reference table.

How to Program Sony Universal Remote With Code Search

You can set your universal remote to search mode and look for the right key code if you are unable to find it at that time. The remote control is forced into search mode by a code in the instructions.

  1. “Turn The Device On” first.
  2. Hold down the “Setup” button for a moment.
  3. Enter the “9-9-1” (three-digit) code after which you must continue to hold down the “Power Button” on the remote control while pressing the Channel up button until the device, in this scenario, your TV, “Turns Off.”

Final Words

Finding your key code may take a little more time using the above method, but it is very crucial. Once you have done the above step your remote should be operating for all the in functionalities.

So, as a final request, kindly forward this article to anyone who might be interested in the Sony VCR universal remote codes. The user will find it easier to select the appropriate code when needed.

Leave a Comment