Philips Universal Remote Codes & Program Instructions

Thank you for choosing a Philips universal remote control. You may replace a damaged or misplaced control with a Philips universal remote or combine many remotes into one through Philips Universal Remote Codes.

The majority of IR infrared-controlled video equipment models and brands can be controlled by this remote control, but not all of them. There’s a chance that this remote will offer features that your equipment doesn’t have. Use only the equipment’s original remote control.

Getting it?

The first step is to add batteries and configure your remote for your specific product and brand after becoming comfortable with it.
We appreciate you purchasing a Philips remote and wish you a long life with it.

Philips Universal Remote Codes List

RCA Universal Remote Codes For Philips

1003, 1004, 1008, 1012, 1019, 1062, 1068, 1069, 1075, 1086, 1087, 1088, 1130, 1132, 1134, 1167, 1183, 1196, 1219, 1235, 1268, 1273, 1291, 1292, 1370, 1377, 1382, 1386, 1390, 1407, 1426, 1434

GE & One-For-All Universal Remote Codes For Philips

0062, 0204, 0184, 0208, 0205, 0206, 0207, 0004, 0189, 0183, 0199, 0200, 0288, 0456, 0003, 0008, 0068, 0075, 0086, 0087, 0141

Magnavox Universal Remote Codes For Philips

0005, 0006, 0007, 0008, 0009

How to Program a Philips Universal Remote

We have listed 3 simple and tested methods to program your universal remote to work with your devices. Here we go.

All of the codes are scanned in the remote during the auto-search procedure. To configure the control, it scans one code at a time to locate the correct remote code that works with your remote. The instructions below must be followed.

1. Turn on the smart device you want to use the universal remote to control, such as the TV.
2. To “turn on” a device, press and hold the TV, DVD, CBL, and OK/SEL buttons for three seconds. Your device is prepared to program, according to the LED light.
3. Use the remote to select the “CH+” and “CH-” switches. On/off indications are displayed on the remote. Continuously press the “up” or “down” key until the device turns off.
4. Click the “power” key to confirm the code. It should start up. If it does, try a different channel to make sure the remote is configured properly.
5. To store the code, press the “device” button now. The device’s LED will flash twice to verify the code that was stored.

2. How to Program Philips Universal Remote With Manual Method

1. You must first “Turn The Device On.”
2. On your “Philips universal remote,” select “TV.”
3. To put the universal remote in “Learning Mode,” press and hold the “Setup button” until it flashes a light.
4. Finally, key in the “Keycode” you obtained from the programming manual (Instructions Booklet)
5. Simply “point your remote at the TV” after completing this step, and then “Press and Hold The Power” button.
6. When the screen goes dark, you can release the “Power Button.”

That’s All!

Your TV should now operate perfectly with the universal remote control. If not, try repeating the process with a new code from the same section of the data table.

3. How to Program Philips Universal Remote With Code Search

You can set your universal remote to search mode and look for the right key code if you are unable to find it at that time. The remote is forced into search mode by a code in the manual.

1. “Turn The Device On” first.
2. Hold down the “Setup” button for a while.
3. Enter the “9-9-1” (three-digit) code after which you must continue to hold down the “Power Button” on the remote control while pressing the Channel up button until the device, in this case, your TV, “Turns Off.”

Finding your key code may take a little more time using the above method, but it is very important. Your remote should function properly for all in-room functions once you have completed these steps.

Troubleshooting Guide

1. How to Check If Philips Universal Remote Control Works?

Tap a button on the remote and use a digital camera to see if the remote’s front light is blinking.

(A digital camera is the only device that can see the light; the human eye cannot)

There can be an issue with your remote’s configuration if the remote displays a flashing light through the digital camera but your device is still not responding.

For more assistance, consult the user manual or get in touch with our help desk.

You might require new batteries or the remote could be broken if it doesn’t reveal a flashing light coming from the digital camera.

2. How to Manually Setup a Universal Remote Control for My Philips TV?

Hold down the “OK” button and the universal mode key (DVD, STB, or HTS) at the same time for 5 seconds.

The three universal mode keys and the TV mode key will flash for one second before staying lit in the selected mode.

Enter the device’s 4-digit RC code to setup the device. The codes for the various devices are listed in the TV’s user manual.

The three universal mode and TV mode keys will flash three times if the code is approved. The remote control has been set up and is ready for use.

The three universal mode and TV mode keys will light up for two seconds if the code entered is wrong, after which the selected universal mode key will remain lighting.

Enter the 4-digit RC code one more time.

You may only set up one device per universal mode on the universal remote control.

3. Where is the Code List for My Philips Universal Remote Control?

Download the instruction manual.

The code list is often located at the end of the user manual.