You want to use a universal remote to operate your Orion TV. In that case, you must program your favorite universal remote control with one of the following codes.
Following the code lists which also have step-by-step instructions for configuring your universal remote. You may also use the other two methods if any of the methods don’t work for you.
Try a different code if the first one doesn’t seem to work. We add new codes to our listings on a regular basis.
Contents
Orion TV Universal Remote 4 Digit Codes List
- 1056
- 1030
- 2028
- 1054
- 2000
- 1230
- 2136
- 2005
- 2108
- 2218
- 1167
- 2007
- 2033
- 2035
- 1133
- 1020
Orion TV Universal Remote 3 Digit Codes List
081, 136, 720, 748
RCA Universal Remote Codes For Orion TV
030, 035, 191, 208, 017, 029, 056, 069, 1030, 1035, 1191, 1024, 1208, 1086, 1090, 1106, 0236, 0463, 1463, 1892, 3540, 10463, 11892, 13540, 13650
GE Universal Remote Codes For Orion TV
035, 121, 135, 0121, 0135, 0035, 5004, 5006, 5039, 5040, 5041, 5046, 5055, 5142, 5177, 5235, 5253, 5441, 0281, 0371, 1771, 1781
VIZIO Universal Remote Codes For Orion TV
0121, 0135, 0035
ONN Universal Remote Codes For Orion TV
5011, 5028, 5060, 5062, 5074
Philips Universal Remote Codes For Orion TV
0713, 0115, 0105
How to Program a Universal Remote to Work With an Orion TV?
There are three simple ways to set up or configure a universal remote to work with your Orion TV. Now we are going to guide you step by step on each one of them.
1. How to Program Orion TV Universal Remote Without Codes
All universal remote control codes are scanned in the remote during the auto search method. To configure the control, it scans one code at a time to figure out the correct remote code that works with your remote. Follow the instructions below.
- Turn on the smart device you want to use the universal remote to control, such as the TV.
- To “turn on” a device, press and hold the TV, DVD, CBL, and OK/SEL buttons for three seconds. The device is prepared to configure, according to the LED light.
- Use the remote to select the “CH+” and “CH-” switches. On/off indications are displayed on the remote. Repeatedly press the “up” or “down” key until the device turns off.
- Click the “power” key to confirm the code. It should start up. If it does, try a different channel to make sure the remote is configured properly.
- To save the code, press the “device” button now. The device’s LED will flash twice to confirm the code that was entered.
2. How to Program Orion TV Universal Remote With Manual Method
- You must first “Turn The Device On.”
- On your “Orion TV universal remote,” select “TV.”
- To put the universal remote in “learning mode,” press and hold the “Setup button” until it flashes a light.
- Finally, key in the “Keycode” you gathered from the programming manual (Instructions Booklet)
- Simply “point your remote at the TV” after finishing this step, and then “Press and Hold The Power” button.
- When the screen goes dark, you can release the “Power Button.”
That’s All!!
Your TV should now operate perfectly with the universal remote control. If not, try repeating the process with a new code from the same section of the data table.
3. How to Program Orion TV Universal Remote With Code Search
You can set your universal remote to search mode and look for the right key code if you are unable to find it at that time. The remote control is forced into search mode by a code in the manual.
- “Turn The Device On” first.
Hold down the “Setup” button for a while.
Type the three-digit “9-9-1” code.
As soon as the device, in this instance, your TV, “Turns Off,” press and hold the “Power Button” on the remote control.
Determining your key code may take a little more time using the above method, but it is very important. Your remote should function properly for all in-room functions once you have completed these steps.
We hope that the above procedures and codes have been used to configure your Orion TV as well as your chosen remote control. For setting up Orion remote controls, those methods are used.
Final Words
We appreciate your feedback, which will help us improve our website and help more people who are waiting for their remote codes. We’d love to accept new universal remote control codes that have worked for you.
Please leave those codes in the comment section below and we will share them with other users by posting them on our website.