Logik DVD Player Universal Remote Codes

Are you tired of using multiple remote controls to handle each device, sometimes selecting the incorrect one? Allow the wonders of the Logik DVD player remote to take charge and do away with the hassle of using multiple remotes.

One of the strongest and most trustworthy brands of universal remote control available today. When programmed into your device, our comprehensive choice of universal Logik DVD remote codes will function perfectly.

It would be simpler to configure the Logik DVD remote once you had matched the code to the brand and model of your device.

Contents

Logik DVD Universal Remote Codes List

We have a range of Logik DVD remote codes that you may use to test out the programming process. You could find it quite difficult to choose the correct Logik universal remote code for your device type because there are so many options available.

Continue attempting the code each time you get it wrong since there is a suitable one for your device in the whole list of Logik DVD universal remote codes that we give here.

Find the right code for your device from the list below:

  • 2304
  • 0713
  • 3681
  • 2382
  • 3805
  • 3177
  • 3542
  • 0884
  • 2195
  • 1832
  • 2644
  • 2594
  • 2439

How to Program Logik DVD Universal Remote

You are making the right decision when you opt to control many devices with a single Logik DVD remote. It may sound a little difficult to configure a Logik DVD remote, but it actually works the opposite way around.

Simple steps and a universal Logik DVD remote are all that is needed for this process to be completed. When programming your Logik DVD remote, follow the instructions below.

How to Program Logik DVD Universal Remote With Auto Search

All universal remote control codes are scanned in the remote during the auto search method.

To configure the control, it scans one code at a time to locate the correct remote code that works with your remote. Follow the instructions below.

  1. Turn on the smart device you want to use the universal remote to control, such as the TV.
  2. To “Turn On” a device, press and hold the TV, DVD, CBL, and OK/SEL buttons for 3 seconds. The device is prepared to configure, according to the LED light.
  3. Use the remote to select the “CH+” and “CH-” switches. On/off indications are displayed on the remote. Continuously press the “up” or “down” key until the device turns off.
  4. Click the “power” key to confirm the code. It should start up. If it does, try a different channel to make sure the remote is configured properly.
  5. To save the code, press the “device” button now. The device’s LED will flash twice to validate the code that was entered.

How to Program Logik DVD Universal Remote With Manual Method

By using the keycode we can easily program a universal remote and the keycode identifies the make and model of your equipment.

  1. You must first “Turn The Device On.”
  2. On your Logik DVD universal remote, select “TV.”
  3. To put the universal remote in “learning mode,” press and hold the “Setup button” until it flashes a light.
  4. Finally, key in the “Keycode” you collected from the programming manual (Instructions Booklet)
  5. Just “point your remote at the TV” after completing this step, and then “Press and Hold The Power” button.
  6. When the screen goes dark, you can release the “Power Button.”

That’s ALL!!

Your TV should now operate perfectly with the universal remote control. If not, try repeating the process with a new code from the same section of the data table.

How to Program Logik DVD Universal Remote With Code Search

You can set your universal remote to search mode and look for the right key code if you are unable to find it at that time. The remote control is forced into search mode by a code in the instructions.

  1. “Turn The Device On” first.
  2. Hold down the “Setup” button for a moment.
  3. Enter the “9-9-1” (three-digit) code after which you must continue to hold down the “Power Button” on the remote control while pressing the Channel up button until the device, in this case your TV, “Turns Off.”

Final Words

Finding your key code may take a little more time using the above method, but it is very important. Your remote should function properly for all in-room functions once you have completed these steps.

It will be very simple to control several devices with the Logik DVD remote. What level of programming expertise do you have? Has this article’s use of codes and instructions proven useful? Leave a message and tell us about your experience.

Your suggestions will help us make this website better. Or feel free to message me here if you wish to share a few codes that aren’t on the list above.

Leave a Comment