Jumbo Universal Remote Codes & Program Instructions

You must configure the remote before you can use it to effortlessly control your TV if you want the Jumbo Universal Remote Codes. The methods listed below must be used if you have no idea how to configure your remote to control your TV.

Once you find a method that works, you may enter the codes to link your TV and this universal remote control with convenience. Try the below methods one by one.

If you’d prefer to start with the list of remote codes, you can find it below; if not, you may skip the table and go directly to the programming instructions.

Contents

Jumbo Universal Remote Codes List

Brand NameCodes
ADMIRAL TV001, 173
AIWA TV195, 196
AKAI TV002
AOC TV009, 014, 132, 156, 175
APEX TV214
AUDIOVOX TV053
CITIZEN TV009, 042, 053, 058, 105, 109, 177
CRAIG TV042, 053
DAEWOO TV018, 019, 042, 058, 082, 085, 097, 100, 126, 127, 130, 138
EMERSON TV035, 036, 037, 038, 039, 040, 041, 042, 043, 045, 049, 051, 053
FUJITSU TV051, 197
FUNAI TV042, 051, 053, 155, 189, 198
GE TV015, 022, 031, 044, 052, 054, 055, 087, 092, 103, 107, 125, 164
HITACHI TV001, 004, 009, 013, 059, 060, 061, 088, 091, 137, 139, 140, 141, 142, 143, 144
HAIER TV216, 217
JENSEN TV004, 009
JVC TV013, 054, 055, 060, 065, 067, 089
LG TV044, 005, 009, 056, 057, 155, 156, 172
MAGNAVOX TV004, 008, 009, 062, 068, 069, 074, 075, 077, 089
MEMOREX TV000, 001, 004, 009, 049, 051, 135
MITSUBISHI TV004, 005, 009, 022, 051, 081, 089, 132, 180
NEC TV003, 004, 005, 009, 010, 085, 089, 095
PANASONIC TV003, 051, 055, 062, 070, 148, 170, 171
PHILIPS TV062, 068, 069, 074, 075, 077, 086, 087, 089, 163, 183
PIONEER TV004, 009, 090, 179, 185
PROSCAN TV000, 015, 031, 107
QUASAR TV003, 054, 055, 062, 070, 148, 170, 171
RCA TV007, 009, 011, 015, 048, 082, 092, 094, 096, 098, 101, 102, 103, 107, 113
SAMSUNG TV004, 005, 009, 015, 104, 105, 106, 109, 172
SANSUI TV135, 136
SANYO TV004, 013, 049, 108, 110, 180, 209
SHARP TV004, 009, 079, 095, 111, 112, 114, 122, 123, 124, 173
SONY TV002, 006, 071, 128
SYLVANIA TV004, 008, 009, 062, 068, 069, 074, 075, 077, 155, 161, 163, 189, 198
TOSHIBA TV013, 049, 089, 105, 109, 117, 118, 120, 159, 178
ZENITH TV000, 001, 004, 023, 038, 058, 059, 064, 073, 121, 135, 136

How to Program Jumbo Universal Remote Without Codes

All universal remote control codes are scanned in the remote during the auto search method. To configure the control, it scans one code at a time to determine the correct remote code that works with your remote. The directions below must be followed.

  1. Turn on the smart device you want to use the universal remote to control, such as the TV.
  2. To “turn on” a device, press and hold the TV, DVD, CBL, and OK/SEL buttons for 3 seconds. The device is prepared to configure, as indicated by the LED light.
  3. Use the remote to select the “CH+” and “CH-” switches. On/off indications are displayed on the remote. Repeatedly press the “up” or “down” key until the device turns off.
  4. Click the “power” key to confirm the code. It should start up. If it does, try a different channel to make sure the remote is configured properly.
  5. To save the code, press the “device” button now. The device’s LED will flash twice to verify the code that was stored.

How to Program Jumbo Universal Remote With Manual Method

By using the keycode we can easily program a universal remote and the keycode identifies the make and model of your equipment.

  1. You must first “Turn The Device On.”
  2. On your “Jumbo Universal Remote,” select “TV.”
  3. To put the universal remote in “learning mode,” press and hold the “Setup button” until it displays a light.
  4. Finally, key in the “Keycode” you gathered from the programming manual (Instructions Booklet)
  5. Simply “point your remote at the TV” after completing this step, and then “Press and Hold The Power” button.
  6. When the screen goes dark, you can release the “Power Button.”

Your TV should now operate flawlessly with the universal remote control. If not, try repeating the process with a new code from the same section of the reference table.

How to Program Jumbo Universal Remote With Code Search

Let’s say you were unable to locate a valid code for your device. In that situation, you might attempt another method to correctly configure your Jumbo universal remote. To find the right code, that method makes use of the universal remote search function.

  1. The device you want to operate must first be turned ON.
  2. Hold down the CODE SEARCH button on the universal remote for a few seconds. Release the CODE SEARCH button once the indicator light turns on.
  3. The device button for the sort of device you want the universal remote control to control should then be pressed and released.
  4. Now, an indicator light needs to blink once and then stay lighted.
  5. Press and then let go of the POWER ON-OFF button while aiming the remote control at the device.
  6. You must hit and release the ENTER button as soon as the device goes off.

Final Words

Getting your key code may take a little longer using the above methods, but it is very important. Your remote should function properly for all in-room functions once you have completed these steps.

Even though we have listed all of the Universal Remote Codes for Jumbo in this article, if you see any errors or think that we have left out any codes, please leave a comment and we will fix the problem as well as add the missing codes.

Leave a Comment