Do you have a JBL Soundbar? If you want to use your favorite remote, cable or satellite remote to control it, then you don’t need to worry about how to operate it. Here we are providing the best universal remote control codes for your JBL Soundbar
In general, any universal remote control code can be used to operate a JBL Soundbar, but occasionally the codes you’ve chosen to program may not work. In these cases, please leave a comment below with the name of your remote control and its brand, and we will respond with the best solution and working codes.
The codes below are now mentioned together with their programming methods.
Contents
1. JBL Soundbar 5 Digit Remote Control Codes
- 30110
- 30281
- 31306
- 32241
2. JBL Soundbar 4 Digit Remote Control Codes
- 4001
- 5009
- 6050
How do I Control My JBL Soundbar With my Universal Remote?
If the remote codes given above didn’t work for your JBL Soundbar, we advise you to manually search the codes using the methods listed here.
How to Program JBL Soundbar Universal Remote Without Codes
All universal remote control codes are scanned in the remote during the auto search method. To configure the control, it scans one code at a time to locate the correct remote code that works with your remote. Follow the guidelines below.
- “Switch On” the smart device like “TV” that you want the universal remote to operate.
- “Turn on” the remote, tap on the device button (TV, DVD, CBL and OK/SEL) for 3 seconds. The LED light indicates the device is ready to program.
- Point out the remote to device and click on “CH+” & “CH-“ switches. Remote will show on/off signals. Press “up” or “down” key continuously till the device will turn off.
- Verify the code by clicking on “power” key. Device should turn on. If it starts, try changing the channel to verify that remote is programmed correctly.
- Now tap the “device” button to save the code. LED of Device will blink twice for confirming the code stored.
How to Program JBL Soundbar Universal Remote With Manual Method
By using the keycode we can easily program a universal remote and the keycode identifies the make and model of your equipment.
- First, you need to “Turn The Device On”
- Press the “TV” on your “JBL Soundbar universal remote”
- Now press and hold the “Setup button” of the Universal Remote until it shows the “Light Flash” (It means it is in “Learning mode”)
- Finally, enter the “Keycode” which you collected from the programming guide (Instructions Booklet)
- Once you’ve done this procedure, just “point your remote at the TV” and then “Press And Hold The Power” button
- You can release the “Power Button” whenever the screen switches off
That’s All! Your TV should now function fine with the universal remote control. If it doesn’t, try repeating the operation with a different code from the same section of the reference table.
How to Program JBL Soundbar Universal Remote With Code Search
If you can’t locate the correct key code for the device at the time, you can configure your universal remote to look for it. It’s a manual code that puts the remote in search mode. You can find that code in your manual.
- The JBL Soundbar remote that you want to replace must first be pointed at with your universal remote.
- Next, depending on the model of your universal remote, press either the SETUP button or the MAGIC button.
- You must now enter the manual programming code that can be found on your universal remote’s instruction manual.
- The next step is to push a universal remote programming button, such as TV VOLUME DOWN.
- Then you must press and hold the matching button on the JBL Soundbar’s original remote control.
- We should notice a light blinking. We can now use the universal remote’s TV VOLUME DOWN command because this function has been correctly saved.
Code Search using Comcast Remote Control
- Switch on your “Soundbar”
- Once hit on the “AUX”
- Then press and hold “Setup” up to the key blinks twice
- Now release “Setup”
- After that you should enter “9 9 1 3” or else “9 9 3”
- Now the “AUX” key will blink two times
- Press the “Power” and then keep the remote control to face at the soundbar
- Until the soundbar “Turns off”, press the “CH+”
- So, in the code search mode, your remote control will send the “IR Codes” from its library to your selected device.
- Once press the “Setup” to “lock in the code”
- Finally, the “AUX” key will blink twice
Code Search using DIRECTV Remote Control
- Switch on your “Soundbar”
- Now “volume up” but “muted”
- Then press “AV1” or “AV2”
- After that press and hold the “Mute” and also “Select” up to 2 blinks
- Then “Enter 9 9 1” and then wait for 2 blinks
- Then enter “3”
- Now press and then release the “Volume up” button
- Now “Face the remote near the soundbar” and then keep on pressing and releasing the “CH+” key
- Finally, the volume will change, then you should press “Select” to lock the code
These methods can be applied to all of the universal remotes that they have described, not just the ones for Comcast or DirectTV. We may easily access our favorite universal remote control codes using the above methods.
Wrapping Up
We value your feedback which will help us to improve our blog and help more people who are waiting for their remote codes. We also accept new universal remote control codes that have worked for you. So please leave those codes in the comment section below and we will share them with other users by posting them on our website.
If you require any more remote codes, please ask us in the comment box below and we will provide them to you.