GE DVR/SAT Combos Universal Remote Codes

If you are using the SAT Combos universal remote control and would like to learn more about the remote’s programming codes and procedures, we’ve listed them here. The universal remote control codes for GE DVR/SAT Combos and the ge 34459 6-device remote control are both very helpful, but they must function.

Here, I will share some of the most recent and functional universal remote control codes for GE DVR/SAT combos, so you may program your remote to control a variety of smart devices across your home using just one device. Without further ado, let’s get started.

Contents

GE DVR/SAT Combos Universal Remote Codes

Brand NameCodes
BELL EXPRESSVU0647, 0655
DISH NETWORK0655, 0647
DREAMBOX0620
ECHOSTAR0655, 0647
EXPRESSVU0647, 0655
FORTEC STAR0569, 0555, 0556
HUGHES NETWORK0621, 0580
RCA0653
PHILIPS0621
PROSCAN0653
SAMSUNG0583
SONY0657, 0659
ULTIMATE TV0653, 0659
ZENITH0656

How to Program GE Universal Remote Without Codes

All universal remote control codes are scanned in the remote during the auto search procedure. To program the control, it scans one code at a time to determine the correct remote code that works with your remote. Follow the directions below:

  1. “Switch On” the smart device like “TV” that you want the universal remote to operate.
  2. “Turn on” the remote, and tap on the device button (TV, DVD, CBL, and OK/SEL) for 3 seconds. The LED light indicates the device is ready to program.
  3. Point out the remote to device and click on “CH+” & “CH-“ switches. Remote will show on/off signals. Press “UP” or “Down” key continuously till the device will “Turn Off”.
  4. Verify the code by clicking on “Power” key. Device should turn on. If it starts, try changing the channel to verify that the remote is programmed correctly.
  5. Now tap the “Device” button to save the code. LED of Device will blink twice for confirming the code stored.

How to Program GE Universal Remote With Manual Method

The universal remote may be readily programmed using the keycode, which also serves to identify the make and model of your equipment.

  1. First you need to “Turn The Device On”
  2. Press the “TV” on your “GE universal remote”
  3. Now press and hold the “Setup button” of the Universal Remote until it shows the “Light Flash” (It means it is in “Learning mode”)
  4.  Finally enter the “Keycode” which you collected from the programing guide (Instructions Booklet)
  5. Once you’ve done this procedure, just “point your remote at the TV” and then “Press And Hold The Power” button
  6. You can release the “Power Button” whenever the screen switches off.

That’s all there is to it; your TV should now operate flawlessly with the universal remote control. If not, try repeating the process with a new code from the same section of the reference table.

How to Program GE Universal Remote With Code Search

If you couldn’t find the key code which works for the device at that time you can setup your universal remote to search mode for the correct one. It’s a code in the manual which forces the remote into the search mode.

  1. First of all “Turn The Device On”
  2. Now press and hold the “Setup” button
  3. Enter the “9-9-1” (three-digit) code
  4. Now hold down the “Power Button” on the remote and then press the Channel up them until the device in this case your tv “Turns Off”.

Final Words

Finding your key code may take a little more time using the above method, but it is very crucial. Your remote should function properly for all in-room functions once you have completed the aforementioned steps.

It’s all about technology now, so use these GE DVR/SAT Combos Universal Remote Codes to enjoy your gadgets and operate them without any hassle from using several remote controls since you will only need one now.

Leave a Comment