GE DVD Recorders + RW Universal Remote Codes

You cannot control your GE DVD Recorders Plus RW unless you have the valid codes. You can get a complete list of the codes that are valid on this platform. You don’t need to bring a different remote for each of your devices. Aside from this, the procedure you must follow is straightforward and simple.

Programming these codes doesn’t require any further knowledge; see here for the GE codes for universal remote. With your favorite GE DVD recorders + RW device, you may now amuse yourself.


GE DVD Recorders + RW Universal Remote Codes List

Brane NameCodes
CENTRIOS0951, 1060, 1061
GO-VIDEO0431, 0902, 0901
JVC0900, 1072
LITEON0902, 0898, 0959
MAGNAVOX[0979], [0980]
MEDION0903, 0959
PHILIPS[0979], [0980]
PHILIPS-MAGNAVOX[0979], [0980]
PIONEER0977, 0909, 1084
SONY0987, 0988, 0989
TOSHIBA0973, 0398
YAMAHA0979, 0980

How to Program GE Universal Remote Without Codes

In the auto search method, all the universal remote codes are gone through the scanning process in the remote. It scans one code at a time to find out the correct remote code that works with your remote to program the control. Follow the instructions given below:

  1. “Switch On” the smart device like “TV” that you want the universal remote to operate.
  2. “Turn on” the remote, tap on the device button (TV, DVD, CBL and OK/SEL) for 3 seconds. The LED light indicates the device is ready to program.
  3. Point out the remote to the device and click on “CH+” & “CH-“ switches. Remote will show on/off signals. Press “up” or “down” key continuously till the device will turn off.
  4. Verify the code by clicking on “power” key. Device should turn on. If it starts, try changing the channel to verify that remote is programmed correctly.
  5. Now tap the “device” button to save the code. LED of the Device will blink twice for confirming the code stored.

How to Program GE Universal Remote With Manual Method

By using the keycode we can easily program a universal remote and the keycode identifies the make and model of your equipment.

  • First, you need to “Turn The Device On”
  • Press the “TV” on your “GE universal remote”
  • Now press and hold the “Setup button” of the Universal Remote until it shows the “Light Flash” (It means it is in “Learning mode”)
  •  Finally, enter the “Keycode” which you collected from the programming guide (Instructions Booklet)
  • Once you’ve done this procedure, just “point your remote at the TV” and then “Press And Hold The Power” button
  • You can release the “Power Button” whenever the screen switches off

That’s all, your TV will work perfectly now with the universal remote control, if your device is not working then try to repeat the same procedure with the different code from the same part of the reference table.

How to Program GE Universal Remote With Code Search

If you couldn’t find the key code which works for the device at that time you can setup your universal remote to search mode for the correct one. Its a code in the manual which forces the remote into the search mode

  • First of all “Turn The Device On”
  • Now press and hold the “Setup” button
  • Enter the “9-9-1” (three-digit) code
  • Now hold down the “Power Button” on the remote and then press the Channel up them until the device in this case your tv “Turns Off”

Finding your key code may take a little more time using the above method, but it is very crucial. Your remote should function properly for all in-room functions once you have completed the aforementioned steps.

Now that the article is over, I hope you can effectively control your GE CABLE Set-top Box devices with the universal remote. And I have no doubt that you will be able to do anything.

All of this has to do with the GE DVD Recorders + RW Universal Remote Codes, and now is the time to watch TV shows and go to the movies without getting a headache. You may now effortlessly programme your remote controls to operate a variety of gadgets.

Leave a Comment