Dynex DVD Player Universal Remote Codes

Do you know how all the components of your home entertainment system might be managed by a single remote control? You can use a Dynex DVD remote to control several devices if you have one. Dynex DVD Player Universal Remote Codes which are extremely important can be entered into the remote in just a few simple steps.

We have the entire list of Dynex DVD player remote codes that relate to the device you select, along with programming instructions.

Contents

Dynex DVD Universal Remote Codes List

Almost all of the universal remote codes for Dynex DVD player codes and other video/audio devices will be included in this page. During configuring, the appropriate universal remote code will be used for the Dynex DVD player and the selected device. The list of Dynex DVD player remote codes is provided below:

Dynex DVD Player Universal Remote 5 Digit Codes

  • 10463
  • 22596
  • 32596
  • 52522
  • 52345
  • 54525

Dynex DVD Player Universal Remote 4 Digit Codes

  • 2596
  • 4235
  • 2455
  • 2255
  • 6126
  • 1710

How to Program Dynex DVD Universal Remote

When you choose to sync the Dynex DVD universal remote with other home entertainment systems, you will experience a variety of benefits. Just remember that when setting up your desired device that Dynex DVD player codes for universal remote are important.

You can configure the Dynex DVD remote by following the steps listed below.

How to Program Dynex DVD Universal Remote Without Codes

All universal remote control codes are scanned in the remote during the auto search procedure. To configure the control, it scans one code at a time to determine the correct remote code that works with your remote. Follow the directions below:

  1. Turn on the smart device you want to use the universal remote to control, such as the TV.
  2. To “turn on” a device, press and hold the TV, DVD, CBL, and OK/SEL buttons for three seconds. The device is prepared to configure, according to the LED light.
  3. Just use the remote to select the “CH+” and “CH-” switches. On/off indications are shown on the remote. Continuously press the “up” or “down” key until the device turns off.
  4. Press the “power” key to confirm the code. It should start up. If it does, try a different channel to make sure the remote is programmed properly.
  5. To store the code, press the “device” button now. The device’s LED will flash twice to verify the code that was stored.

How to Program Dynex DVD Universal Remote With Manual Method

By using the keycode we can easily program a universal remote and the keycode identifies the make and model of your equipment.

  1. You must first “Turn The Device On.”
  2. On your “Dynex DVD universal remote,” select “TV.”
  3. So, to put the universal remote in “learning mode,” press and hold the “Setup button” until it flashes a light.
  4. Finally, key in the “Keycode” you got from the programming manual (Instructions Booklet)
  5. Simply “point your remote at the TV” after finishing this step, and then “Press and Hold The Power” button.
  6. When the screen goes dark, you can release the “Power Button.”

That’s all, your TV should now function fine with the universal remote control. If it doesn’t, try repeating the operation with a different code from the same section of the reference table.

How to Program Dynex DVD Universal Remote With Code Search

You can set your universal remote to search mode and look for the right key code if you are unable to find it at that time. The remote control is placed into “Search Mode” by a code in the instructions.

  1. First of all “Turn The Device On”
  2. Now press and hold the “Setup” button
  3. Enter the “9-9-1” (three-digit) code
  4. Now hold down the “Power Button” on the remote and then press the Channel up them until the device in this case your tv “Turns Off”

Conclusion

The above procedure may take a little longer, but it is critical to find your key code. After you’ve completed the above steps, your remote should be functional for all in-room functions.

Have you finished configuring the Dynex DVD remote? Please share your thoughts on this article if you enjoyed it. You can message us with the correct code related to what type of device you used. Please leave your opinions in the comment section below.

Leave a Comment