DVD Universal Remote 4 Digit Codes

With the help of the DVD Universal 4-digit codes, we may control our DVD player as well as the audio and video devices that are connected to any brand of DVD. The 4-digit device code must be entered into your DVD universal tv remote in order to run any of your DVD devices. You must look inside the battery compartment or it may be on the back of the remote if you want to find the model number of your remote control.


DVD Universal Remote Codes 4 Digit

Brand NameCodes
Apex0386, 0390, 0391
B & K0978
Broksonic0932, 0967, 0394
Centrios0951, 1067, 1068, 0921
Classic0431, 1051, 0401
Coby0926, 0946, 0947, 0916, 0445
Cyberhome0393, 0985, 0939
Cytron0446, 0388
Daewoo0440, 0441, 0444, 0971, 0965
Denon0400, 0421
Dual0447, 0984, 0956, 0428, 0446
Durabrand0449, 0405, 0446
Dvd 20000402
Elta0434, 0435
Emerson0405, 0940, 0899, 0456, 0458
Funai0456, 0458
GE0409, 0430
Go-video0431, 0937, 0971, 0454, 0902
Gpx0936, 0944
Harman Kardon0427
Hitachi0404, 0407, 0428, 0419
Ilo0959, 1070
Insignia0405, 0456, 0921, 0430, 0905
Initial0430, 1070
Jvc0406, 0964, 0900, 1072
Jwin0390, 0893, 0895
Kenwood0400, 0429
Klh0430, 0906, 0386
Konka0410, 0411, 0412
Koss0415, 0388
Lasonic0451, 0948
Lenoxx0931, 0435
LG0405, 0972, 0907
Magnavox0398, 0408, 0979, 0981, 0980
Marantz0398, 0405, 0408, 0423, 0981
Memorex0446, 1050
Onkyo0422, 0975
Panasonic0396, 0400, 0974, 0970
Philips0398, 0408, 0423, 0755, 0979, 0981
Pioneer0403, 0404, 0976, 0977
Polaroid0385, 0957, 0949
Polk0398, 0408, 0981
Proscan0409, 0890
Radio Shack0449, 0453, 0919, 0920
RCA0409, 0430, 0449, 0453, 0920, 0890
Samsung0407, 0454, 0942, 0963, 0891, 0455
Sansui0394, 0967
Sanyo0904, 0416
Selectron1077, 1078, 1079
Sharp0397, 0897, 0908
Sony0987, 0988, 0989, 0399, 0986, 0389
Sylvania0456, 0458
Teac0404, 0449
Techwood0433, 1071
Tevion0388, 0446, 0447, 0448, 0450, 0451, 0452
Tivo0912, 0909
Toshiba0394, 0398, 0973, 0924, 0983
Yamaha0400, 0420, 0979, 0980, 0408
Zenith0405, 0907

How to Program DVD Universal Remote Without Codes

All universal remote control codes are scanned in the remote during the auto search procedure. To configure the control, it scans one code at a time to determine the correct remote code that works with your remote. Follow the directions below:

  1. Turn on the smart device you want to use the universal remote to control, such as the TV.
  2. To “turn on” a device, press and hold the TV, DVD, CBL, and OK/SEL buttons for three seconds. The device is prepared to configure, according to the LED light.
  3. Use the remote to select the “CH+” and “CH-” switches. On/off indications are displayed on the remote. Continuously press the “up” or “down” key until the device turns off.
  4. Click the “power” key to confirm the code. It should start up. If it does, try another channel to make sure the remote is configured properly.
  5. To save the code, press the “device” button now. The device’s LED will flash twice to verify the code that was stored.

How to Program DVD Universal Remote With Manual Method

By using the keycode we can easily program a universal remote and the keycode identifies the make and model of your equipment.

  1. You must first “Turn The Device On.”
  2. On your DVD universal remote, select “TV.”
  3. To put the universal remote in “Learning Mode,” press and hold the “Setup button” until it flashes a light.
  4. Lastly, key in the “Keycode” you gathered from the programming manual (Instructions Booklet)
  5. Simply “point your remote at the TV” after completing this step, and then “Press and Hold The Power” button.
  6. When the screen goes dark, you can release the “Power Button.”

That’s all, your TV should now operate flawlessly with the universal remote control. If not, try repeating the process with a new code from the same section of the reference table.

How to Program DVD Universal Remote With Code Search

You can set your universal remote to search mode and look for the right key code if you are not able to find it at that time. The remote control is forced into search mode by a code in the instructions.

  1. First of all “Turn The Device On”
  2. Now press and hold the “Setup” button
  3. Enter the “9-9-1” (three-digit) code
  4. Now hold down the “Power Button” on the remote and then press the Channel up them until the device in this case your tv “Turns Off”

The above procedure may take a little longer, but it is essential to find your key code. After you’ve followed the above steps, your remote should be functional for all in-room functions.

Leave a Comment