Cybertec Universal Remote Codes & Program Instructions

Users of Cybertec devices have been using universal remote controls to operate their equipment with remote controls like the RM-8in1 and RM-L1107+3. If you’re looking for Cybertec universal remote codes, you’ve come to the right blog. Here, you can find all different kinds of functional codes that you may input into your TV using your preferred remote control.

Prior to providing the ideal instructions for configuring your universal remote control, we will first discuss the codes.

Contents

Cybertec rm 8 in 1 & rm-l1107+3 Universal Remote 3 Digit Codes List

092, 018, 063, 099, 023, 008, 011, 018, 021, 024, 025, 033, 037, 039, 040, 049, 050, 051, 091, 113, 123, 375, 378

Cybertec rm 8 in 1 & rm-l1107+3 Universal Remote 4 Digit Codes List

0094, 0154, 0170, 0190, 1065, 1075, 1114, 1081, 1827, 1829, 1515, 1733, 1516, 1456, 1073, 1112, 1031, 1264, 1205, 1646, 1268, 1743, 1191, 1333, 1064, 1099, 1332, 1095, 1166, 1164, 1832, 1717, 1414, 1313

How To Program Cybertec TV Universal Remote?

There are three ways to configure any universal remote control to work with your tv. If you use the procedures listed below, your television will function properly. So, if you have the codes from the list of codes above, let’s look at the methods.

How to Program Cybertec Universal Remote Without Codes?

All universal remote control codes are scanned in the remote during the auto search procedure. To configure the control, it scans one code at a time to determine the correct remote code that works with your remote. Follow the directions below:

  1. Turn on the smart device you want to use the universal remote to control, such as the TV.
  2. To “turn on” a device, press and hold the TV, DVD, CBL, and OK/SEL buttons for three seconds. The device is prepared to configure, according to the LED light.
  3. Use the remote to select the “CH+” and “CH-” switches. On/off indications are displayed on the remote. Continuously press the “up” or “down” key until the device turns off.
  4. Click the “power” key to confirm the code. It should start up. If it does, try a different channel to make sure the remote is configured properly.
  5. To store the code, press the “device” button now. The device’s LED will flash twice to verify the code that was stored.

How to Program Cybertec Universal Remote With Manual Method

The universal remote may be readily configured using the keycode, which also serves to identify the make and model of your equipment.
  1. You must first “Turn The Device On.”
  2. On your “Cybertec universal remote,” select “TV.”
  3. To put the universal remote in “Learning Mode,” press and hold the “Setup button” until it flashes a light.
  4. Finally, key in the “Keycode” you gathered from the programming manual (Instructions Booklet)
  5. Simply “point your remote at the TV” after completing this step, and then “Press and Hold The Power” button.
  6. When the screen turns off, you can release the “Power Button.”

That’s all, your TV should now function fine with the universal remote control. If it doesn’t, try repeating the operation with a different code from the same section of the reference table.

How to Program Cybertec Universal Remote With Code Search

You can set your universal remote to search mode and look for the right key code if you are unable to find it at that time. The remote control is forced into search mode by a code in the instructions.

  1. To begin with, “Turn The Device On.”
  2. Press and hold the “Setup” button right now.
  3. Enter the three-digit code “9-9-1” while holding down the “Power Button” on the remote. Then, press the Channel up button until the device, in this case, your TV, “Turns Off.”

Final Words

Locating your key code may take a little more time using the above method, but it is very important. Your remote should function properly for all in-room functions once you have completed the aforementioned steps.

We hope that these techniques and codes have been used to configure your Cybertec television as well as your preferred remote control. For setting up Cybertec remote controls, those techniques are employed.

If you tried any of the above codes and they didn’t work for your device, try the alternate codes that are listed above. If you’re still having problems, leave a comment below, and we’ll do our best to help you out and solve the problem.

Leave a Comment