Comcast Xfinity Universal Remote Codes & Program Instructions

Have you ever used universal remote codes or become curious about these remote controls? Would you like to program your Comcast universal remote using the codes, including three-digit, four-digit, and any other codes that are compatible with it?

Why wait?

Just use the methods listed below to learn how to setup your device with your preferred remote controllers by entering the codes as instructed.

Contents

Comcast Universal Remote Codes List

Brand NameCodes
LG10178, 11265
Panasonic10051, 10250
Samsung10812, 10060
Sanyo10154, 10159
Sony10000, 11100
Sharp10093, 10165
Toshiba10156, 11156
Vizio11758, 11756

Comcast Universal Remote 4 Digit Codes

  • 0497
  • 0030
  • 0056

Comcast Universal Remote 5 Digit Codes

  • 10000
  • 10178
  • 10812
  • 11291
  • 10036
  • 10019
  • 10434
  • 11704
  • 11704
  • 10030

How to Program Comcast Universal Remote Without Codes

All universal remote control codes are scanned in the remote during the auto search procedure. To configure the control, it scans one code at a time to determine the correct remote code that works with your remote. Follow the directions below:

  1. Turn on the smart device you want to use the universal remote to control, such as the TV.
  2. To “Turn On” a device, press and hold the TV, DVD, CBL, and OK/SEL buttons for 3 seconds. The device is prepared to configure, according to the LED light.
  3. Use the remote to select the “CH+” and “CH-” switches. On/off indications are displayed on the remote. Continuously press the “up” or “down” key until the device turns off.
  4. Click the “power” key to confirm the code. It should start up. If it does, try a different channel to make sure the remote is configured properly.
  5. To store the code, press the “device” button now. The device’s LED will flash twice to verify the code that was stored.

How to Program Comcast Universal Remote With Manual Method

We can quickly code a universal remote using the keycode, and the keycode identifies the make and model of your equipment.
  1. You must first “Turn The Device On.”
  2. On your Comcast universal remote, select “TV.”
  3. To put the universal remote in “learning mode,” press and hold the “Setup button” until it flashes a light.
  4. Lastly, key in the “Keycode” you gathered from the programming manual (Instructions Booklet)
  5. Simply “point your remote at the TV” after completing this step, and then “Press and Hold The Power” button.
  6. When the screen goes dark, you can release the “Power Button.”

That’s it; the universal remote control will now operate your TV flawlessly. If it still doesn’t work, try repeating the process with a new code from the same section of the reference table.

How to Program Comcast Universal Remote With Code Search

You can set your universal remote to search mode and look for the right key code if you are unable to find it at that time. The remote control is forced into search mode by a code in the instructions.

  1. “Turn The Device On” first.
  2. Hold down the “Setup” button for a moment.
  3. Enter the “9-9-1” (three-digit) code after which you must continue to hold down the “Power Button” on the remote control while pressing the Channel up button until the device, in this case, your TV, “Turns Off.”

Locating your key code may take a little more time using the above method, but it is very significant. Your remote should function properly for all in-room functions once you have completed these mentioned steps.

Conclusion

A wide list of codes for your universal remote has been provided. Additionally, we have walked you through every step of the various ways to configure your universal remote. We truly hope that the universal remote codes and programming techniques were helpful for you.

Use the search function in the top bar to locate any other devices you may have. As an alternative, you can visit our site and go through the brands or categories to find them. We’re delighted we could be of assistance.

Leave a Comment