Comcast Cable Soundbar Universal Remote Codes & Program Instructions

Comcast audio component remote codes are typically 5 digits long and have been assigned as universal remote codes, meaning they should operate with all home theatre systems and sound bars. For this Comcast, we have a lot of codes that you may program using straightforward procedures.

Comcast remotes can now be programmed using a variety of techniques, including automatic search and manual way. In order to connect your remote to your device, attempt the below methods.


Comcast Universal Remote Codes For Sound Bar, Audio and Home Theater

These codes are also applicable to sound bars, audio, and home theatre systems, so simply select your brand, select the code, and enter it into your remote.

Brand NameRemote Codes
Aiwa30158, 30189, 30405
Bose31229, 31933
Denon31360, 31104
Harman/Kardon30110, 30189
Kenwood31313, 31570, 30027, 31027
Magnavox30189, 30531
Onkyo30135, 30842
Optimus31023, 30531
Panasonic31308, 31518
Philips30189, 31266
Pioneer31023, 30014, 30531, 31384
Polk Audio30189
RCA31023, 31254, 30531
Sanyo31261, 31469, 31801
Sony31759, 30158, 31758
Technics31308, 31518
Wards30158, 30189, 30014
Yamaha30176, 31176

How to Program Comcast Cable Soundbar Universal Remote Without Codes

All universal remote codes are scanned in the remote when using the auto search method. To configure the control, it scans one code at a time to discover the correct remote code that works with your remote. Follow the steps indicated below:

  1. Turn on the smart device you want to use the universal remote to control, such as the TV.
  2. To “turn on” a device, press and hold the TV, DVD, CBL, and OK/SEL buttons for three seconds. The device is prepared to programme, according to the LED light.
  3. Use the remote to select the “CH+” and “CH-” switches. On/off indications are displayed on the remote. Continuously press the “up” or “down” key until the device turns off.
  4. Click the “power” key to confirm the code. It should start up. If it does, try a different channel to make sure the remote is configured properly.
  5. To store the code, press the “device” button now. The device’s LED will flash twice to verify the code that was stored.

How to Program Comcast Cable Soundbar Universal Remote With Manual Method

We can quickly configure a universal remote using the keycode, and the keycode identifies the make and model of your equipment.
  1. You must first “Turn The Device On.”
  2. On your “Comcast Cable Soundbar universal remote,” select “TV.”
  3. In order to put the universal remote in “learning mode,” press and hold the “Setup button” until it flashes a light.
  4. At last, key in the “Keycode” you gathered from the programming manual (Instructions Booklet)
  5. Simply “point your remote at the TV” after finishing this step, and then “Press and Hold The Power” button.
  6. When the screen fades, you can release the “Power Button.”

That’s All !

Your TV should now function fine with the universal remote control. If it doesn’t, try repeating the operation with a different code from the same section of the reference table.

How to Program Comcast Cable Soundbar Universal Remote With Code Search

If you can’t locate the correct key code for the device at the time, you can configure your universal remote to look for it. It’s a manual code that puts the remote in search mode.

  • First of all “Turn The Device On”
  • Now press and hold the “Setup” button
  • Enter the “9-9-1” (three-digit) code
  • Now hold down the “Power Button” on the remote and then press the Channel up them until the device in this case your tv “Turns Off”

Final Words

Finding your key code may take a little more time using the above method, but it is very necessary. Once you’ve completed the aforementioned steps, your remote should operate in all modes.

We hope the aforementioned techniques and codes have been used to set your Comcast Cable Soundbar as well as your preferred remote. For Comcast Cable Soundbar remote control setup, those techniques are employed.

If you require any assistance with the universal remote control codes, please leave your question, and we will resolve it as soon ASAP.

Leave a Comment