COBY TV’s Universal Remote Codes & Program Instructions

Did you ever use a universal remote control? If not, go out and buy one right away. In this discussion, we’ll show you how to use a universal remote control to operate a COBY TV. The codes include working three-digit and four-digit codes.

You must be aware of the procedures required to configure the universal remote control for your Coby TV. The procedures are outlined below, but first, we’ve provided a list of codes. Check them out right away and see which code will work with this remote.


Coby TV 5 Digit Universal Remote Codes

  • 01376
  • 11538
  • 12017
  • 10178
  • 12003
  • 11531
  • 11265
  • 11314

Coby TV 4 Digit Universal Remote Codes

  • 1538
  • 2017

COBY TV Universal 3 Digit Remote Codes

505, 626, 627, 594, 633, 593, 720, 607, 604, 699, 005, 205, 625, 266, 165, 267, 256, 056, 257, 262

How to Program COBY Universal Remote Without Codes

All universal remote control codes are scanned in the remote during the auto search procedure. To configure the control, it scans one code at a time to determine the correct remote code that works with your remote. Follow the directions below:

  1. “Turn On” the smart device you want to use the universal remote to control, such as the TV.
  2. To “turn on” a device, press and hold the TV, DVD, CBL, and OK/SEL buttons for three seconds. The device is prepared to configure, according to the LED light.
  3. Use the remote to select the “CH+” and “CH-” switches. On/off indications are displayed on the remote. Repeatedly press the “up” or “down” key until the device turns off.
  4. Click the “power” key to confirm the code. It should start up. If it does, try a different channel to make sure the remote is configured properly.
  5. To store the code, press the “device” button now. The device’s LED will flash twice to verify the code that was stored.

How to Program COBY Universal Remote With Manual Method

The universal remote may be readily configured using the keycode, which also serves to identify the make and model of your equipment.
  1. You must first “Turn on Your Device.”
  2. On your “COBY Shack universal remote,” select “TV.”
  3. So, to put the universal remote in “learning mode,” press and hold the “Setup button” until it flashes a light.
  4. Finally, key in the “Keycode” you gathered from the programming manual (Instructions Booklet)
  5. Simply “aim your remote at the TV” after completing this step, and then “Press and Hold The Power” button.
  6. When the screen turns off, you can release the “Power Button.”

That’s all; your TV should now function fine with the universal remote control. If it doesn’t, try repeating the operation with a different code from the same section of the reference table.

How to Program COBY Universal Remote With Code Search

If you can’t locate the correct key code for the device at the time, you can configure your universal remote to look for it. It’s a manual code that puts the remote in search mode.

  1. “Turn The Device On” first.
  2. Hold down the “Setup” button for a moment.
  3. Enter the “9-9-1” (three-digit) code after which you must continue to hold down the “Power Button” on the remote control while pressing the Channel up button until the device, in this case your TV, “Turns Off.”

Wrapping Up

Finding your key code may take a little more time using the above technique, but it is very necessary. Your remote should function properly for all in-room functions once you have completed these mentioned steps.

Codes are shown above work with both the Coby 8-in-1 universal remote and Coby 5 in 1 universal remote for manual setup. We sincerely hope that this article was very helpful. If you encountered any difficulties when using the above-mentioned approaches, please let us know in the comment area below.

Leave a Comment