Chunghop DVD Universal Remote Codes & Program Instructions

You must utilize the Chunghop Universal DVD Remote Codes if you want to make your life easy. Basically, you will find the list of codes on every platform. Sometimes these universal codes will not function. As a result, you will find the codes here that are error-free and functioning properly.

Now that we’ve looked at the list of universal remote codes, let’s look at how to use them so you can see the results while your remote and device are linked.


Chunghop Universal DVD Remote Codes List

Brand NameRemote Codes
TCL000, 015, 039, 054, 055
Shinco001, 010
Malata002, 009, 023, 024, 073
Nintaus003, 071, 079, 080, 081, 082, 090, 093
Samsung004, 017, 049
Qisheng005, 037
Shanshui013, 046
BBK018, 021, 027, 028, 033, 048, 078, 091
SAST020, 059, 060, 076
Skyworth018, 022, 025, 032, 034, 058, 096, 097
Dansai026, 074
Huabao018, 029, 061, 062, 063
Panda038, 051, 052, 053
Toshiba041, 069
Victor047, 084
Brand064, 065
Emerson066, 067
Dihe070, 077
Dayu086, 087
Caixing088, 095

How to Program Chunghop DVD Universal Remote Without Codes

All universal remote control codes are scanned in the remote during the auto search procedure. To configure the control, it scans one code at a time to determine the correct remote code that works with your remote. Follow the directions below:

  1. “Switch On” the smart device like “TV” that you want the universal remote to operate.
  2. “Turn on” the remote, tap on the device button (TV, DVD, CBL and OK/SEL) for 3 seconds. The LED light indicates the device is ready to program.
  3. Point out the remote to device and click on “CH+” & “CH-“ switches. Remote will show on/off signals. Press “up” or “down” key continuously till the device will turn off.
  4. Verify the code by clicking on “power” key. Device should turn on. If it starts, try changing the channel to verify that remote is programmed correctly.
  5. Now tap the “device” button to save the code. LED of Device will blink twice for confirming the code stored.

How to Program Chunghop DVD Universal Remote With Manual Method

We can quickly code a universal remote using the keycode, and the keycode identifies the make and model of your equipment.
  1. You must first “Turn The Device On.”
  2. On your “Chunghop DVD universal remote,” select “TV.”
  3. To put the universal remote in “learning mode,” press and hold the “Setup button” until it flashes a light.
  4. At last, key in the “Keycode” you gathered from the programming manual (Instructions Booklet)
  5. Simply “aim your remote at the TV” after completing this step, and then “Press and Hold The Power” button.
  6. When the screen goes dark, you can release the “Power Button.”

That’s it; the universal remote control will now operate your TV flawlessly. If it still doesn’t work, try repeating the process with a new code from the same section of the reference table.

How to Program Chunghop DVD Universal Remote With Code Search

You can set your universal remote control to search mode if you are unable to find the key code that operates the gadget at that moment. There is a manual code that causes the remote to enter the search mode.

  1. First of all “Turn The Device On”
  2. Now press and hold the “Setup” button
  3. Enter the “9-9-1” (three digit) code
  4. Now hold down the “Power Button” on the remote and then press the Channel up them until the device in this case your tv “Turns Off”


Finding your key code may take a little more time using the above method, but it is very crucial. Your remote should function properly for all in-room functions once you have completed the these steps.

Now, I’m confident that this advice will assist you in learning the Chunghop Universal DVD Remote Codes. There is no longer a need to look for the list of correct universal codes. And I can guarantee that you won’t run into any difficulties.

Leave a Comment