Bose Soundbar Universal Remote Codes

If you have a Bose soundbar, you may use any of your favourite universal remote controls to operate it by programming it properly and using the relevant working codes. Check out the codes listed below, then use the techniques listed below to put them into your remote. So you can acquire the 4-digit Bose soundbar remote codes from this blog post.

You can configure your universal remote controls by checking the codes below and entering them.

Bose Soundbar Universal Remote 4 Digit Codes

• 1229
• 1256
• 0666
• 3741
• 1960
• 1280

Bose Soundbar Universal Remote 5 Digit Codes

• 31934
• 31935
• 11144
• 30189
• 31933
• 31517
• 20752
• 01982
• 31229

GE Universal Remote Codes For Bose Soundbar

• 00027
• 01885

Bose Soundbar Universal Remote Codes List

Before You Follow The Below Methods just keep in mind: Change the settings in the Bose system’s “Menu” so that it may accept IR commands from an infrared remote. Actually, the Bose systems are configured to respond to RF orders by default.

How to Program Bose Soundbar Universal Remote without Codes

All universal remote control codes are processed by the remote’s scanning procedure in the auto search method. To program the control, it examines each code individually to determine which is the right one to use with your remote. The steps listed below should be followed:

1. “Switch On” the smart device like “TV” that you want the universal remote to operate.
2. “Turn on” the remote, tap on the device button (TV, DVD, CBL and OK/SEL) for 3 seconds. The LED light indicates the device is ready to program.
3. Point out the remote to device and click on “CH+” & “CH-“ switches. Remote will show on/off signals. Press “up” or “down” key continuously till the device will turn off.
4. Verify the code by clicking on “power” key. Device should turn on. If it starts, try changing the channel to verify that remote is programmed correctly.
5. Now tap the “device” button to save the code. LED of Device will blink twice for confirming the code stored.

How to Program Bose Soundbar Universal Remote With Manual Method

1. You must first “Turn The Device On.”
2. On your “Bose Soundbar universal remote,” select “TV.”
3. To put the universal remote in “learning mode,” press and hold the “Setup button” until it flashes a light.
4. At last, key in the “Keycode” you gathered from the programming manual (Instructions Booklet)
5. Simply “point your remote at the TV” after completing this step, and then “Press and Hold The Power” button.
6. When the screen turns off, you can release the “Power Button.”

That’s all there is to it; your TV should now operate flawlessly with the universal remote control. If not, try repeating the process with a new code from the same section of the reference table.

How to Program Bose Soundbar Universal Remote With Code Search

You can set your universal remote to search mode and look for the right key code if you are unable to find it at that time. The remote is forced into search mode by a code in the handbook.

1. “Turn The Device On” first.
2. Hold down the “Setup” button for a moment.
3. Enter the “9-9-1” (three-digit) code after which you must continue to hold down the “Power Button” on the remote control while pressing the Channel up button until the device, in this case your TV, “Turns Off.”

Final Words

Finding your key code may take a little more time using the above method, but it is very crucial. Your remote should function properly for all in-room functions once you have completed the aforementioned steps.

An wide list of codes for your universal remote has been provided. Additionally, we have walked you through each step of the various ways to programme your universal remote.

We sincerely hope that the universal remote codes and programming techniques were successful for you.

Use the search function in the top bar to locate any other devices you may have. As an alternative, you can visit our site and go through the brands or categories to find them.