Aiwa TV’s Universal Remote Codes & Program Instructions

You must program your preferred universal remote by using the codes shown below in order to control your Aiwa TV remote with it. Try the codes next to the ones that don’t seem to be working if the remote seems to be malfunctioning. You need to know the codes—three, four, or whatever digits work best—and the setup procedure to link up your TV remote with your preferred universal remote.

Check them one by one from the lines below. All of the codes are listed below, along with the processes. If these codes don’t work, try the ones below.

Aiwa TV’s Universal Remote 3 Digit Codes

• 109
• 192
• 402
• 185
• 037
• 064
• 039

Aiwa TV’s Universal Remote 4 Digit Codes

3512, 1505, 0701, 1916, 1908, 0705, 0195, 0196, 0227, 0269, 0411, 0651, 0931, 1411, 4731, 4801, 1155, 1164, 1488, 1512, 1034, 1036, 0121, 0221, 0324, 0528, 5011, 5295, 5296, 5309, 1032, 1236

Aiwa TV’s Universal Remote 5 Digit Codes

11362, 10701, 11914, 10032, 11916, 17342, 14102, 16507, 19307, 14118, 18041, 12248, 12270

RCA Universal Remote Codes For Aiwa TV

036, 1036, 1032, 1236, 1362, 11362

GE & One-For-All Universal Remote Codes For Aiwa TV

0195, 0196, 0227, 0269

Philips Universal Remote Codes For Aiwa TV

0121, 0221, 0324, 0528

How To Program Aiwa TV Universal Remote?

You must get the code from the list above and enter it as instructed in the next four stages in terms of setting up your Aiwa remote control with your preferred universal remote.

First Method:

The first technique is the one you should use; if it doesn’t work, use the other usual procedures that are listed below:

1. Press and hold the “Clear TV button” continuously until all “Four Lights Illuminate.”
2. You must “Select The Code” here.
3. Now, simply hit the “Pound” button once.
4. When your “TV Turns Off,” you must press and release the “Red Power Button.”

How to Program Aiwa TV Universal Remote Without Code

All universal remote control codes are scanned in the remote during the auto search procedure. To configure the control, it scans one code at a time to determine the correct remote code that works with your remote. Follow the directions below:

1. “Switch On” the smart device like “TV” that you want the universal remote to operate.
2. “Turn on” the remote, tap on the device button (TV, DVD, CBL and OK/SEL) for 3 seconds. The LED light indicates the device is ready to program.
3. Point out the remote to the device and click on “CH+” & “CH-“ switches. Remote will show on/off signals. Press “up” or “down” key continuously till the device will turn off.
4. Verify the code by clicking on “power” key. Device should “Turn On”. If it starts, try changing the channel to verify that remote is programmed correctly.
5. Now tap the “device” button to save the code. LED of Device will blink twice for confirming the code stored.

How to Program Aiwa TV Universal Remote With Manual Method

1. You must first “Turn The Device On.”
2. On your “Aiwa TV Universal Remote”, select “TV.”
3. In order to put the universal remote in “Learning Mode,” press and hold the “Setup button” until it flashes a light.
4. At last, key in the “Keycode” you gathered from the programming manual (Instructions Booklet)
5. Simply “aim your remote at the TV” after completing this step, and then “Press and Hold The Power” button.
6. When the screen dims, you can release the “Power Button.”